• 8871 Merrimac Lane N. Maple Grove, MN 55311, USA

Pipe line leak repair kit

Inquire Now

    WRAP SEAL QUICK REPAIR KIT FOR PIPE LEAKS FEATURES:

    • Repairs leak in 30 minutes
    • Applicable to pipes up to 18″ (457 mm) diameter
    • Applicable on any metal or non-metal pipes
    • Repairs T-joint, elbow joint, valve thread, valve body
    • Withstand pressure up to 400 psi (28 kg/cm2)
    • Withstand temperature up to 200 °C (392 °F)
    • Safe for drinking water and resistant to most chemicals
    • Reinforce and strengthen pipe after repair
    • Permanent repair and extend service life of pipes

    APPLICABLE MATERIAL:

    • Steel
    • Copper
    • Aluminium
    • Galvanized steel
    • PVC
    • CPVC
    • Stainless steel
    • Polyethylene
    • Polypropylene
    • Cast-iron
    • Concrete
    • FRP/GRE

    CHEMICAL RESISTANCE:

    • Oil
    • Water (drinking water, wastewater, steam)
    • Solvents (acetone, toluene, MEK, ethyl alcohol)
    • Mild acids (hydrochloric acid, sulfuric acid) and alkalis
    • Chemical (ethylene glycol, xylenes, ammonia)
    • Hydrocarbons
    • Bases
    • Slurries
    • Fuels (petroleum, diesels, gasoline)
    • Gases (LNG, LPG)
    • Organic salts

    WORKING TIME (FIBERGLASS TAPE):

    •  1 minute at 30 °C (86 °F)

    CURING TIME:

    • 30 minutes at 30 °C (86 °F)
    • Heat may be applied to decrease curing time
    • Unopened foil pouch may be immerse in cold water prior to repair to add working and curing time.

    APPLICATION:

    • Pipe repairs
    • Offline repairs
    • Sealing joints
    • Hazardous material spill control
    • Reinforce thinning walls
    • Abrasion protection
    • Structural reinforcement
    • Repairs in hard to reach areas
    • Underwater repairs

    OPERATING TEMPERATURE:

    • Continuous – From -29 °C (-20 °F) up to 200 °C (392 °F)
    • Intermittent – From 200 °C (392 °F) up to 320 °C (570 °F)

    OPERATING PRESSURE:

    • Recommended for pressure up to 400 psi (28 kg/cm2)
    • (Results vary depending on pipe size, type of pipe, hole size, pipe content and method of application)

    APPLICABLE INDUSTRIES:

    Building & Facilities

    Electronics

    Industrial Processing

    Irrigation

    Oil & Gas

    Chemical

    Manufacturing Plants

    Marine

    Military

    Offshore

    Food Processing

    Petrochemical

    Pharmaceutical

    Power Generation

    Pulp & Paper

    Wastewater

    Water Distribution

    Building & Facilities

    TECHNICAL DATA:

    • Pressure tested
    • 1/2″ (15 mm) steel pipe with 1/8″ (3 mm) hole when repaired with Wrap Seal withstands 4000 psi (281 kg/cm2)
    • 1/2″ (15 mm) steel pipe with 1/2″ (13 mm) hole when repaired with Wrap Seal withstands 600 psi (42 kg/cm2)
    • Tensile strength
    • 3920 psi (276 kg/cm2)
    • Bond strength
    • 230 psi (16 kg/cm2)
    • Tensile elongation
    • 1.2 % ± 0.7 %
    • Compressive strength
    • 13750 ± 530 psi (967 ± 37 kg/cm2)
    • Yield strength
    • 2260 psi (159 kg/cm2)
    • Cured hardness
    • 82 Shore D

    WRAP SEAL OFFLINE LEAK REPAIR PROCEDURE:

    Stop the pipe flow
    Roughen the area to be repaired
    Knead the Seal Stic
    Apply the Seal Stic to fill in holes or crack of the damaged or leak area.
    Immerse the Wrap Seal Fiberglass Tape into water
    Wrap the Wrap Seal Fiberglass Tape around the repair area as tightly and evenly as possible
    Discard the plastic tube at the end of the roll
    gloves in water and quickly compress the bubbling resins back into the fiberglass wrap
    Continue to polish the wrap until all bubbling has stopped. Repair completed with smooth and hard ivory appearance